Recherche de site Web

Configurer un serveur FTP étape par étape dans CentOS 6.5


Ce tutoriel vous montre comment installer et configurer un serveur FTP sous CentOS 6.5. Bien que les étapes fournies ici aient été testées sur CentOS 6.5, elles devraient également fonctionner sur RHEL 6.x (x représentant la version) et Scientific Linux 6.x. Dans ce tutoriel, l'adresse IP et le nom d'hôte de mon serveur FTP sont respectivement 192.168.1.200 et mainserver.ostechnix.com. J'ai déjà configuré un dépôt local et je vais installer FTP depuis mon dépôt local. Pour plus d'informations, rendez-vous sur configurer votre dépôt local dans CentOS 6/RHEL 6/Scientific Linux.

Avant de continuer, arrêtez le pare-feu.

[root@mainserver ~]# service iptables stop
iptables: Flushing firewall rules:                         [  OK  ]
iptables: Setting chains to policy ACCEPT: filter          [  OK  ]
iptables: Unloading modules:                               [  OK  ]
[root@mainserver ~]# service ip6tables stop
ip6tables: Flushing firewall rules:                        [  OK  ]
ip6tables: Setting chains to policy ACCEPT: filter         [  OK  ]
ip6tables: Unloading modules:                              [  OK  ]
[root@mainserver ~]# chkconfig iptables off
[root@mainserver ~]# chkconfig ip6tables off
[root@mainserver ~]#

Maintenant, installons le service FTP.

[root@mainserver ~]# yum install -y vsftpd
[root@mainserver ~]# Start vsftpd service.
[root@mainserver ~]# service vsftpd start
Starting vsftpd for vsftpd:                                [  OK  ]
[root@mainserver ~]#

Activer vsftpd à des niveaux multi-utilisateurs.

[root@mainserver ~]# chkconfig vsftpd on

Maintenant, modifiez le fichier /etc/vsftpd/vsftpd.conf. Décommentez et modifiez les lignes dans le fichier vsftpd.conf qui sont indiquées en gras.

[root@mainserver ~]# cat /etc/vsftpd/vsftpd.conf 
# Example config file /etc/vsftpd/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options.
# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's
# capabilities.
#
# Allow anonymous FTP? (Beware - allowed by default if you comment this out).
anonymous_enable=NO
#
# Uncomment this to allow local users to log in.
local_enable=YES
#
# Uncomment this to enable any form of FTP write command.
write_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
local_umask=022
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
#anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
#
# The target log file can be vsftpd_log_file or xferlog_file.
# This depends on setting xferlog_std_format parameter
xferlog_enable=YES
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#chown_uploads=YES
#chown_username=whoever
#
# The name of log file when xferlog_enable=YES and xferlog_std_format=YES
# WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log
#xferlog_file=/var/log/xferlog
#
# Switches between logging into vsftpd_log_file and xferlog_file files.
# NO writes to vsftpd_log_file, YES to xferlog_file
xferlog_std_format=YES
#
# You may change the default value for timing out an idle session.
#idle_session_timeout=600
#
# You may change the default value for timing out a data connection.
#data_connection_timeout=120
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#nopriv_user=ftpsecure
#
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that on some FTP servers, ASCII support allows a denial of service
# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
# predicted this attack and has always been safe, reporting the size of the
# raw file.
# ASCII mangling is a horrible feature of the protocol.
ascii_upload_enable=YES
ascii_download_enable=YES
#
# You may fully customise the login banner string:
ftpd_banner=Welcome to OSTECHNIX FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
# (default follows)
#banned_email_file=/etc/vsftpd/banned_emails
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
#chroot_local_user=YES
#chroot_list_enable=YES
# (default follows)
#chroot_list_file=/etc/vsftpd/chroot_list
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
ls_recurse_enable=YES
#
# When "listen" directive is enabled, vsftpd runs in standalone mode and
# listens on IPv4 sockets. This directive cannot be used in conjunction
# with the listen_ipv6 directive.
listen=YES
#
# This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6
# sockets, you must run two copies of vsftpd with two configuration files.
# Make sure, that one of the listen options is commented !!
#listen_ipv6=YES
pam_service_name=vsftpd
userlist_enable=YES
tcp_wrappers=YES
use_localtime=YES

Maintenant, redémarrons le service vsftpd et essayons de nous connecter au serveur FTP.

[root@mainserver ~]# service vsftpd restart
Shutting down vsftpd:                                      [  OK  ]
Starting vsftpd for vsftpd:                                [  OK  ]

Connectez-vous au serveur FTP.

Remarque : Par défaut, l’utilisateur root n’est pas autorisé à se connecter au serveur FTP pour des raisons de sécurité. Créons donc un nouvel utilisateur appelé ostechnix.

[root@mainserver ~]# useradd ostechnix
[root@mainserver ~]# passwd ostechnix
Changing password for user ostechnix.
New password: 
BAD PASSWORD: it is based on a dictionary word
Retype new password: 
passwd: all authentication tokens updated successfully.

Connectez-vous au serveur FTP en utilisant le nouvel utilisateur ostechnix.

[root@mainserver ~]# ftp 192.168.1.200
-bash: ftp: command not found
[root@mainserver ~]#

Oups ! Le package ftp n'est pas installé. Alors installons d'abord le package ftp.

[root@mainserver ~]# yum install -y ftp
Loaded plugins: fastestmirror
Loading mirror speeds from cached hostfile
Setting up Install Process
Resolving Dependencies
--> Running transaction check
---> Package ftp.i686 0:0.17-51.1.el6 will be installed
--> Finished Dependency Resolution
Dependencies Resolved
================================================================================
 Package       Arch           Version                 Repository           Size
================================================================================
Installing:
 ftp           i686           0.17-51.1.el6           localrepo            55 k
Transaction Summary
================================================================================
Install       1 Package(s)
Total download size: 55 k
Installed size: 91 k
Downloading Packages:
Running rpm_check_debug
Running Transaction Test
Transaction Test Succeeded
Running Transaction
Warning: RPMDB altered outside of yum.
  Installing : ftp-0.17-51.1.el6.i686                                       1/1 
  Verifying  : ftp-0.17-51.1.el6.i686                                       1/1 
Installed:
  ftp.i686 0:0.17-51.1.el6                                                      
Complete!
[root@mainserver ~]#

Reconnectez-vous au serveur FTP.

[root@mainserver ~]# ftp 192.168.1.200
Connected to 192.168.1.200 (192.168.1.200).
220 Welcome to OSTECHNIX FTP service.
Name (192.168.1.200:root): ostechnix
331 Please specify the password.
Password:
500 OOPS: cannot change directory:/home/ostechnix
Login failed.
ftp>

Il affiche une erreur indiquant que l'utilisateur ne peut pas changer dans son répertoire $HOME. Tapez exit pour revenir de la console ftp et permettre au démon vsftpd de changer d'utilisateur vers leurs répertoires $HOME. Pour ce faire, mettez à jour la configuration SELinux en utilisant la commande ci-dessous.

[root@mainserver ~]# setsebool -P ftp_home_dir on

Et enfin, connectez-vous au serveur FTP.

[root@mainserver ~]# ftp 192.168.1.200
Connected to 192.168.1.200 (192.168.1.200).
220 Welcome to OSTECHNIX FTP service.
Name (192.168.1.200:root): ostechnix
331 Please specify the password.
Password:
230 Login successful.
Remote system type is UNIX.
Using binary mode to transfer files.
ftp> pwd
257 "/home/ostechnix"
ftp>

Ça fonctionne maintenant. Vous pouvez utiliser votre serveur FTP.

Se connecter au serveur FTP en utilisant Filezilla depuis le client :

Téléchargez et installez le logiciel client Filezilla sur l'un des systèmes clients. Ouvrez le client Filezilla et saisissez le nom d'utilisateur et le mot de passe que nous avons créés précédemment, puis cliquez sur connecter.

Se connecter au serveur FTP via le navigateur depuis le client :

Ouvrez le navigateur et accédez à ftp://192.1168.1.200. Entrez le nom d'utilisateur et le mot de passe que nous avons créés précédemment.

Si vous voulez naviguer sur un serveur FTP en utilisant un nom de domaine (c'est-à-dire ftp://ostechnix.com) au lieu de l'adresse IP, ajoutez l'IP du serveur FTP dans les enregistrements du serveur DNS. Pour plus d'informations sur la configuration du serveur DNS, consultez Configurer le serveur DNS dans CentOS 6.3/RHEL 6.3/Scientific Linux 6.3.

C'est tout. Vous pouvez accéder à votre serveur FTP depuis n'importe quel client maintenant en utilisant Filezilla, ainsi que depuis votre navigateur web client.

Bonne journée !!!